|
|
|
|
37151 39 12 1 |
|
Опции темы | Поиск в этой теме |
04.12.2016, 17:44 | 1 |
Модератор своих разделов
Регистрация: 03.07.2010 Последняя активность: 10.10.2022 08:53 Адрес: Copenhagen, Denmark
Сообщений: 1652
Сказал(а) спасибо: 0
Поблагодарили: 2982 раз(а) в 1024 сообщениях
|
Test/review of Charger Xtar VP4 Plus Dragon
Charger Xtar VP4 Plus Dragon
Xtar has many good LiIon chargers, this is the new top of line model. It can charge 4 round cell, a 3S battery pack and a smartphone, it can also measure capacity, or work as a power bank and it has a cell resistance and voltage meter. It comes in a cardboard box (I got the charger without a box and the pictures is supplied by Xtar). In the box is a bag that contains the charger and accessories, there is also an elastic strip to hold batteries. The contents of the bag is the charger, a power supply, the resistance (IR)/voltage probes, car charger, instruction sheet, welcome note and warranty card. The probes are four terminal and uses a usb connector. The 4 terminal connection means that it will automatic compensate for any wire resistance and connection resistance at the charger, but it cannot compensate for connection resistance at the battery with the supplied probes. The probes are spring loaded and has a rough surface to get better connection. The charger has a DC connector for power input, two usb connectors, one for the IR probes and one for power output. There is also a JST-XH connector to charge a 3S LiIon battery pack. Because the charger is "only" charging at 1A this function do not need the main connection to the battery pack. The charger has a large screen, four leds and 3 buttons: Current/Refresh button: A short press will change current setting, a long press will start a refresh cycle. Display: A short press will change between displayed slots (With 1 or 2 batteries the display will always show the correct slots), a long press will set the display to lowest brightness, a double click will return to main screen. Record/Test: A short press will recall test data (The result of test runs is automatically saved), a long press will start a test cycle, a double click will turn sound on/off. When showing recorded data the buttons has functions to step between records and delete records. When display brightness is reduced the first keypress will restore it to full brightness. The leds uses colors to show the functions: Blue: Discharge, this is valid for both refresh/test and power bank function. Red: Battery charging Green: Battery full or slot empty Off: Battery empty in power bank or power bank not turned on. Here is the full display captured during power on. Normal charging at 1A. Discharge during refresh mode, the blocks are animated to show that the charger is discharging. When volt/ohm mode is enabled and the probes connected to a battery the display will change between ohm and volt. The 3S charging do not have much display space, only one icon, flashing while charging and steady when done. The charger uses the typical construction with a slider, this time with a very long connection at the plus pole making it possible to handle D and 32650 cells. The slots can handle from 30.5mm to 72.8mm. The charger can handle 70 mm long batteries, inclusive flat top cells. Measurements
Lion charging The LiIon charging can charge 4 cells with 0.5A or 1A and two cells with 2A. This is a good CC/CV charge curve with termination current around 80mA Display shows 2916mAh The other slots are also fine. On #3 the charger starts reducing current a bit earlier for some reason. Display shows: 2766mAh, 2860mAh, 2900mAh The 2600 and 3400mAh cells are handled fine. Display shows: 2599mAh and 3232mAh The old 2600mAh cell is mostly charged in CV mode (As expected), the charger handles it fine. Display shows: 2253mAh I did get time for a single run with my new test cell, it works as expected. Display shows: 3384mAh Charging with lower current will reduce the termination current to about 40mA (Good). This works very well with the small cells. Display shows: 717mAh and 488mAh The charger can charge two batteries at 2A, this is for larger cells and high current cells. The termination current is increased to about 120mA. At 1A it is possible to charge four cells. Display shows: 2918mAh, 2899mAh, 2917mAh, 2931mAh Using my own 12V supply I can see it uses a bit below 2A when charging. M1: 33,1°C, M2: 34,4°C, M3: 34,5°C, M4: 32,2°C, M5: 36,2°C, M6: 36,6°C, HS1: 49,2°C M1: 33,5°C, M2: 35,1°C, M3: 35,2°C, M4: 33,4°C, M5: 42,1°C, M6: 36,0°C, HS1: 44,5°C The charger needs about 8 seconds to initialize, before it will charge. It is possible to change current at any time during a charger. LiIon Refresh The refresh function will discharge and charge a cell, the display will show both discharged and charged capacity. The discharge current is either 0.25A or 0.5A, depending on selected charge current. With 1A charge current the discharge current is 0.5A and the cell is discharged down to about 2.6V, this is fine for most modern cells. After the discharge there is a 5 minute rest, before the cell is charged again. Display shows: dis:2916mAh, charge:2925mAh The other 3 slots looks the same. Display shows: dis: 2783mAh, 2840mAh, 2851mAh, charge: 2804mAh, 2872mAh, 2843mAh With 0.5A charge current the discharge current is 0.25A. Display shows: dis:2897mAh, charge:2946mAh At 2A charge current the discharge current is 0.5A, i.e. the same as 1A discharge current. Display shows: dis:2927mAh, charge:2942mAh It is possible to refresh four cells at a time. Display shows: dis:2819mAh, 2962mAh, 2930mAh, 3051mAh, charge: 2929mAh, 2953mAh, 2974mAh, 2983mAh M1: 38,3°C, M2: 40,5°C, M3: 39,6°C, M4: 36,0°C, M5: 46,7°C, M6: 44,8°C, HS1: 59,5°C Discharging LiIon the charger needs to get rid of some heat. It handles it fine without a fan, the cells stays at an acceptable temperature. The discharge is done with constant current, not pwm (nice). LiIon Test The test mode will charge, discharge and charge again. Used discharge current is the same as in refresh mode. Charging first means the full capacity is measured during discharge. Display shows: dis:2873mAh, charge: 2885mAh NiMH charging The charger starts with a low charge current (0.1A), before it switches to the selected current. On this charge curve it uses a voltage termination followed by a two hour top-off charge of around 50mA Display shows: 1622mAh With these two cells it uses a -dv/dt termination, but they still gets the top-off charge. And here is another voltage termination. The 3 high capacity cells are handled fine. Termination is a bit slow on the worn down eneloopXX, but that is acceptable. Display shows: 2597mAh, 2433mAh and 2449mAh It do also terminate at 0.5A on a AA cell. Display shows: 1831mAh No problems with the AAA cell. The top-off is still two hours, but with lower current (nice). Display shows: 620mAh The 2A charge is also started at low current and looks fine. Display shows: 1666mAh Due to the first 10 minutes at low current it takes about 13 minutes to detect the full cell. This time on voltage, it will use longer time if it needs to use -dv/dt detection. Display shows: 53mAh Four cells at once. Display shows: 1813mAh, 1719mAh, 1856mAh and 1793mAh Using my own 12V power supply I can see the current drain is about 1A. M1: 38,2°C, M2: 40,1°C, M3: 38,5°C, M4: 37,9°C, M5: 37,3°C, HS1: 48,6°C The charger needs between 6 and 7 seconds to initialize a NiMH charge. The low current charge will last for 10minutes, before the charger switches to selected current. It is possible to change current at any time. As usual with NiMH chargers the current is turned off for voltage checking. Top-off charge is done with pulses at the selected current. The top-off current will be about 6% of the selected charge current. Here is the 2A top-off pulses. NiMH Refresh Refresh mode will discharge and then charge the cell. Discharge current will depend on selected charge current. 0.5A charge means 0.25A discharge, 1A and 2A charge means 0.5A discharge. The charger insist on doing the 10minutes low current charge, before starting on the discharge. The discharge is down to about 0.85 volt. After the discharge there is a 5 minute pause, before the battery is charged. Display shows: dis:1921mAh, charge 1702mAh Display shows: dis:1889mAh, 1846mAh, 1880mAH, 1877mAh, charge 1926mAh, 1692mAh, 1876mAh, 1665mAh With 0.5A charge current the discharge current is 0.25A. Display shows: dis:1931mAh, charge: 1926mAh At 2A the discharge is 0.5A Display shows: dis:1889mAh, charge: 1692mAh The charger can discharge four cells at once. Display shows: dis:1904mAh, 1866mAh, 1919mAh, 1898mAh, charge: 1877mAh, 1863mAh, 1907mAh, 1891mAh M1: 32,9°C, M2: 34,3°C, M3: 34,1°C, M4: 32,0°C, M5: 35,1°C, M6: 34,7°C, HS1: 43,4°C The charger stays cool when discharging NiMH batteries. The discharge current at different charge settings. NiMH test The test will charge, discharge and charge again. The charger do not use a top-off charge before discharging when terminated on voltage, this may give a slightly low capacity for some cells. Display shows: dis:1868, charge: 1701 3S battery pack The charger can also do a balancing charge on 3S battery packs with a JST-XH connector. The charger do not use the main leads to the battery pack, only the balancing connector, this is acceptable due to the fairly low charge current (For a RC pack). The charger uses a 1A charge current and will do a CC/CV charge. It looks like there is a slight voltage difference between the charged cells (This test was done with new unused cells). Here the battery pack contained 1 full cell and two empty cells. The charger balances them fine. During charge the current is pulsed, probably to allow measuring without have trouble with wire resistance. Internal resistance and voltage measurement To start IR measurement the probes must be shorted, to leave IR mode double click the display button, the charger will also leave IR mode after about 10 minutes. Due to the way the measurements are done the charger can only measure batteries, not resistors. The above values is with LiIon cells, the result is a little bit on the low side, but very consistent. With NiMH the results are a better, but due to the 150mOhm maximum I could not do the last row. The RI is measured with a short 1A current pulse A new measurement is done each 2.5 seconds. The voltmeter function works from 0.66V to 4.49V and is within 0.01V The probes must not be used on the batteries in the charger! USB output
With a single 18650 battery I could draw about 2.2A before output voltage starts to drop. Output is switched off at 2.7A. With four batteries the output can be maintained up to 2.7A. With external power it can also deliver 2.7A. With four batteries it can maintain 0.5A output for about 11 hours. Using only one battery the time is down to 2½ hour. At 1A the output can be maintained for 6 hour. And at 2A it will maintain output for 3 hours. With one battery it will maintain output, but not for very long. With mains power and 2.5A out it did run for one hour. The IR photos below are taken about 45 minutes into the one hour run. M1: 39,8°C, M2: 37,2°C, M3: 45,5°C, HS1: 51,7°C M1: 45,3°C, M2: 56,5°C, HS1: 92,9°C M1: 51,4°C, HS1: 63,9°C As a power bank the usb output has very low noise, at 0.5A it is 8mV rms and 58mVpp. At 1A it is 13mV rms and 78mVpp. At 2A it is 27mV rms and 133mVpp The noise is also very low when mains powered. At 0.5A it is 25mV rms and 119mVpp. At 1A it is 23mV rms and 104mVpp. At 1A it is 20mV rms and 131mVpp. Testing the transformer with 2830 volt and 4242 volt between mains and low volt side, did not show any safety problems. Conclusion This charger has many functions with a fairly simple user interface:
Notes The charger was supplied by Xtar for review. Here is an explanation on how I did the above charge curves: How do I test a charger
__________________
My website with reviews of charges, batteries and other stuff: http://www.lygte-info.dk/ |
Поблагодарили: 16 раз(а) |
Black Night (15.02.2017), Drex (06.10.2021), Ikepod (04.12.2016), Kzakkttixx (10.12.2016), LEV-UA (04.12.2016), Li-Ion (04.12.2016), m72 (17.12.2016), mic1968 (24.01.2018), NazarSunrise (13.12.2016), ostro169 (21.12.2016), Rocklight (04.12.2016), Tankist_20 (26.12.2016), tushich (11.01.2017), Алексей Миронович (20.10.2020), Бармалей (04.12.2016), Сумской (06.12.2016)
|
04.12.2016, 18:56 | 2 |
Ветеран Фонарёвки
Регистрация: 11.05.2012 Последняя активность: 01.04.2019 17:22
Сообщений: 5147
Сказал(а) спасибо: 1116
Поблагодарили: 1650 раз(а) в 958 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Нда... Хтар отмочил так отмочил!
__________________
Фонарей много не бывает! |
09.12.2016, 20:57 | 3 | ||
Увлеченный
Регистрация: 03.12.2012 Последняя активность: 16.11.2021 00:12
Сообщений: 340
Сказал(а) спасибо: 86
Поблагодарили: 59 раз(а) в 45 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
потроха посмотреть надо бы, уже косяки есть
|
||
09.12.2016, 23:24 | 4 |
Увлеченный
Регистрация: 01.11.2014 Последняя активность: 15.05.2024 00:10
Сообщений: 90
Сказал(а) спасибо: 7
Поблагодарили: 16 раз(а) в 16 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
|
10.12.2016, 22:00 | 5 |
Новичок
Регистрация: 28.05.2013 Последняя активность: 10.06.2019 22:19
Сообщений: 3
Сказал(а) спасибо: 0
Поблагодарили: 0 раз(а) в 0 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
мда на бумаге выглядит просто отменно))) так как надо я бы сказал))))
|
17.12.2016, 14:10 | 6 | ||
Участник форума по OpenID
Регистрация: 04.11.2015 Последняя активность: 17.02.2017 07:38
Сообщений: 9
Сказал(а) спасибо: 1
Поблагодарили: 9 раз(а) в 5 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Вчера мне приехала.
Распаковка, первые впечатления и теста записал в ролик
Пока разбираюсь дальше. |
||
Поблагодарили: 3 раз(а) |
07.02.2017, 10:28 | 7 |
Денис
Регистрация: 11.05.2011 Последняя активность: 09.11.2021 11:46 Адрес: Samara
Сообщений: 708
Сказал(а) спасибо: 169
Поблагодарили: 281 раз(а) в 116 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
|
07.02.2017, 14:01 | 8 |
Денис
Регистрация: 11.05.2011 Последняя активность: 09.11.2021 11:46 Адрес: Samara
Сообщений: 708
Сказал(а) спасибо: 169
Поблагодарили: 281 раз(а) в 116 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
На самом деле как ответили с завода, это первая в мире бракованная зарядка. Уже новую выслали.
|
14.02.2017, 14:57 | 9 |
Ветеран Фонарёвки
Регистрация: 08.10.2011 Последняя активность: 02.12.2019 14:07
Сообщений: 14463
Сказал(а) спасибо: 8046
Поблагодарили: 3817 раз(а) в 2645 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Енот, нравится? Стоит приобресть? Про косяки какие то пишут?
|
16.02.2017, 14:41 | 10 |
Новичок
Регистрация: 16.02.2017 Последняя активность: 13.07.2022 11:52
Сообщений: 36
Сказал(а) спасибо: 18
Поблагодарили: 2 раз(а) в 1 сообщении
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Всех приветствую! Понравилась зарядка, прочитал про неё практически всё, что пока есть, в основном на ttp://www.candlepowerforums.com/ Вот одного понять не могу, как в ней реализован режим refresh? В основном все пишут лишь о том, что такой режим есть, а хотелось бы детальный обзор именно этого режима. Полностью ли Dragon позволит отказаться от La Crosse/Maha или их китайских аналогов для корректного восстановления Ni-Mh аккумуляторов? Или эта функция является очень второстепенной для этого прибора и о каком-то сравнении с профильными устройствами речи быть не может?
|
17.02.2017, 07:37 | 11 |
Участник форума по OpenID
Регистрация: 04.11.2015 Последняя активность: 17.02.2017 07:38
Сообщений: 9
Сказал(а) спасибо: 1
Поблагодарили: 9 раз(а) в 5 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Режим Refresh
Пригодится для «оживления» никелевых аккумуляторов. Активируется длительным нажатием на кнопку current/refresh. Зарядка последовательно заряжает/разряжает и снова заряжает аккумуляторы заданным током. Это и многое другое есть в моем обзоре этой зарядки - здесь |
Поблагодарили: 1 раз |
mic1968 (09.02.2018)
|
17.02.2017, 12:06 | 12 | |
Новичок
Регистрация: 16.02.2017 Последняя активность: 13.07.2022 11:52
Сообщений: 36
Сказал(а) спасибо: 18
Поблагодарили: 2 раз(а) в 1 сообщении
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Цитата:
|
|
11.05.2017, 09:24 | 13 |
Увлеченный
Регистрация: 08.02.2012 Последняя активность: 10.04.2020 08:37
Сообщений: 257
Сказал(а) спасибо: 25
Поблагодарили: 8 раз(а) в 7 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Цитата:
Но если махи нет то это вполне сгодится! куча циклов не так уж и нужна при нормальных аккумуляторах. ВЕРДИКТ: надо брать!
__________________
Fenix TK41 JetBeam BС25 JetBeam BA10 Tank007 E09 |
20.07.2017, 15:47 | 14 |
Ветеран Фонарёвки
Регистрация: 08.10.2011 Последняя активность: 02.12.2019 14:07
Сообщений: 14463
Сказал(а) спасибо: 8046
Поблагодарили: 3817 раз(а) в 2645 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Нет ли инструкции на русском?
|
08.12.2017, 21:57 | 15 |
Новичок
Регистрация: 04.12.2017 Последняя активность: 28.12.2023 16:53 Адрес: Собянинск
Сообщений: 22
Сказал(а) спасибо: 3
Поблагодарили: 3 раз(а) в 3 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
При длительном нажатии refresh не только запускается режим разряда (судя по наблюдениям все порты, даже независимо, одновременно аккумуляторы поставлены, или один чуть позже), но и нажатием этой кнопки меняется показание силы тока 05/1А.
Первые впечатления так сказать. |
08.12.2017, 22:25 | 16 |
Новичок
Регистрация: 04.12.2017 Последняя активность: 28.12.2023 16:53 Адрес: Собянинск
Сообщений: 22
Сказал(а) спасибо: 3
Поблагодарили: 3 раз(а) в 3 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Прочёл обзор Александра Квазиса. Так как нужна была полная информация, по возможностям зарядника.
Вот что заметил, как утверждает автор обзора: Режим TEST Предназначен для определения емкости в mAh на заряд и разряд литиевых и никелевых аккумуляторов. Активируется зажатием кнопки Record/Test, и так же производит — заряд/разряд/заряд аккумуляторов заданным током. С никелем похоже такой фокус не прокатывает, ибо в режиме тест, загораются прочерки на экране на какое то время, и далее просто продолжается заряд. |
07.01.2018, 16:36 | 17 |
Ветеран Фонарёвки
Регистрация: 08.10.2011 Последняя активность: 02.12.2019 14:07
Сообщений: 14463
Сказал(а) спасибо: 8046
Поблагодарили: 3817 раз(а) в 2645 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Занялся я экспериментированием.
Взял два аккумулятора. Подписал их "1" и "2". Поставил в Dragon. "1" в 3 слот, "2" в 4-й. Запустил "TEST". Дозарядились до 100% (ток 1А), начался разряд. Разрядились до 1%, постояли 5 минут и начали заряжаться. Зарядились. Смотрю емкость - "1" 2153 на разряде и 2175 на заряде. "2"- 2219 на разряде и 2221 на заряде. Меряю сопротивление "1"- 53, "2" - 60. На следующий день беру эти же аккумуляторы (заряженные) и ставлю их наоборот - "1" в 4 слот, "2" в третий. Запускаю "TEST". Начинается дозаряд - 2% на нос. Пошел разряд. 5 минут. Заряд. И что мы видим? "1"- 2175\2176, "2"- 2145\2175. Вот тебе и Dragon! |
09.01.2018, 15:05 | 18 |
Ветеран Фонарёвки
Регистрация: 08.10.2011 Последняя активность: 02.12.2019 14:07
Сообщений: 14463
Сказал(а) спасибо: 8046
Поблагодарили: 3817 раз(а) в 2645 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Никто коммент не добавит?
|
10.01.2018, 13:43 | 19 |
сволочь фонарёвки
Регистрация: 27.05.2011 Последняя активность: Сегодня 06:26 Адрес: Россия, Пермский край
Сообщений: 38202
Сказал(а) спасибо: 5983
Поблагодарили: 32958 раз(а) в 15289 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
Tankist_20, а какой ты хочешь коммент?
то, что при втором замере слилось меньше, чем в предыдущем? это нормально. то что есть разница между каналами менее 2%? а какая погрешность измерений задекларирована у данного устройства? повтори первый тест и сравни цифры [Исправлено: galex, 10.01.2018 в 13:44] |
Поблагодарили: 1 раз |
Tankist_20 (10.01.2018)
|
10.01.2018, 15:25 | 20 |
Ветеран Фонарёвки
Регистрация: 08.10.2011 Последняя активность: 02.12.2019 14:07
Сообщений: 14463
Сказал(а) спасибо: 8046
Поблагодарили: 3817 раз(а) в 2645 сообщениях
|
Re: Test/review of Charger Xtar VP4 Plus Dragon
|